| The
ALUMINUM SHIELD METAL ROOF SYSTEM is a waterproofing and rust preventative
coating system specifically designed for the special needs of metal roofs.
It is not simply a coating. Instead, it's a combination
of three common-sense products that form an aluminum shield over
metal roofs to waterproof, prevent rust and corrosion, insulate, beautify
and protect. And it does its job so well that it's guaranteed! |
Neglected industrial,
commercial, agricultural and educational metal roofs
are everywhere.
Cleaning can be done
with pressure air (as in photo), detergent or chemical
wash, wire brush or
whatever process is available.
WATERPROOFS
The
ALUMINUM SHIELD METAL ROOF SYSTEM is specifically
designed to waterproof metal roofs.
This is accomplished by using ALUMINUM QUICK-PATCH on seams and fastener
heads to seal leaking or potential leaking areas. Texas Refinery's ALUMINUM
QUICK-PATCH is fast and easy to apply because it is self-adhering. Just
peel the backing off and stick it in place. It's flexible and gives long-lasting
waterproofing protection.
Here, ALUMINUM QUICK-PATCH
has been used to seal over fastener heads.
ALUMINUM QUICK-PATCH
provides an effective waterproof seal around vents
ant other protrusions.
STOPS
RUST AND CORROSION
The first step in the ALUMINUM
SHIELD METAL ROOF SYSTEM is a coating of Texas
Refinery's ANTI-OXIDENE COATING. This stops rust and corosion immediately.
Rust and corrosion are the biggest enemies of a metal roof. Eventually
all metal roofs will rust and corrode and if left untreated, they will
completely deteriorate. If rust and corrosion have not yet begun to form,
this system prevents
them from starting. But even if rust and corrosion have started, the ALUMINUM
SHIELD SYSTEM stops
these destructive forces from doing further damage.
INSULATES
The ALUMINUM SHIELD
METAL ROOF SYSTEM provides a gleaming coat
of protective aluminum over the entire roof. This can reflect as much as
80% of the sun's ultraviolet rays, helping retard surface degradation and
prevent heat from ever entering the building. Cooler interiors mean
energy savings!
EASY
TO APPLY
This system is
fast and easy to apply! In fact, it's so easy that it is ideal for do-it-yourself
applications. No expensive labor is required. First, QUICK-DRY ANTI-OXIDENE
COATING is applied. Next, ALUMINUM QUICK-PATCH is applied to all seams
and fasterner heads to seal leaking or potential leaking areas. And then,
an aluminum topcoat is applied to the entire roof. It's that fast, easy,
effective and economical.
QUICK-DRY ANTI-OXIDENE
is easily applied to the roof by spray, brush of roller.
Under favorable conditions,
QUICK-DRY ANTI-OXIDENE needs to dry for only a few hours.
REDUCES
ROOF MOVEMENT
With the ALUMINUM
SHIELD METAL ROOF SYSTEM, roof surfaces are
kept at the same relative temperature. This helps eliminate thermal shock
which causes expansion and contraction of metal roofs. This lack of movement
means longer life for metal roofs.
BEAUTIFIES
Even older, rusted metal roofs are restored
to like-new brilliance with the ALUMINUM METAL SHIELD
ROOF SYSTEM. Pure aluminum flakes give a long lasting, bright finish
that enhances property value.
A beautiful cover
of ALUMINUM ROOF COATING, SUPER ALUMINUM ROOF COATING
or TEXOTROPIC finishes
the job for ultimate protection.
The ALUMINUM
SHIELD METAL ROOF SYSTEM is a wise investment
on the farm
or
in the city.
APPLICATION
INSTRUCTIONS
PREPARATION:
Roof surface must be prepared properly.
The surface must be clean, sound and free of dirt, dust,
loose rust or other loose particles. Wire brush rusted areas. Damaged metal
that is severely rusted or too thin for self support must be replaced.
Inspect all screws and fasteners carefully. Retighten or replace as necessary.
Clean surface thoroughly and allow to dry.
PRIMING THE SURFACE:
After the surface has been properly prepared, apply QUICK-DRY ANTI-OXIDENE
COATING to the entire roof surface by brush, roller or spray at the rate
of approximately 300 square feet per gallon on flat surfaces or 200 square
feet per gallon on corrugated surfaces. Allow to dry completely.
WATERPROOFING THE SURFACE:
Apply 3-inch wide ALUMINUM QUICK-PATCH to all vertical and horizontal seams
by aligning the roll, peeling back release paper, and pressing into place
directly over seam. For best results, work with no more than twelve inches
at a time.
Apply 3" x 3" ALUMINUM QUICK-PATCH patches over every fastener head. Note:
roofs which have high-profile screws or fasteners may require larger patches
to provide secure bonding around fasteners. It is recommended such patches
be custom-cut from 6" wide ALUMINUM QUICK-PATCH.
TOPCOATING THE SURFACE:
Apply on of Texas Refinery's aluminum
coatings:
ALUMINUM ROOF COATING Non-Fibered
300 square feet per gallon on flat surfaces
200 square feet per gallon on corrugated surfaces
SUPER ALUMINUM ROOF COATING Lightly-Fibered
200 square feet per gallon on flat surfaces
150 square feet per gallon on corrugated surfaces
TEXOTROPIC FIBERED ALUMINUM ROOF COATING
Heavily-Fibered
100 square feet per gallon on flat surfaces
70 square feet per gallon on corrugated surfaces
When the entire
three-step ALUMINUM SHIELD METAL ROOF
SYSTEM is applied,
the following warranties are available:
THREE YEARS - when ALUMINUM ROOF COATING or
SUPER ALUMINUM ROOF COATING is used
as a topcoat.
SIX YEARS - when TEXOTROPIC FIBERED ALUMINUM
ROOF COATING is used as a topcoat.
Required
roof information form must be completed and filed with Texas Refinery Corp.
and account must be paid in full before warranty will be validated.
|
|